Typically used with Mitsubishi DSM & Evolution speed density conversions Typically used with Mitsubishi DSM & Evolution speed density conversions.ĭuralast GM 3/8" NPT air intake temperature sensor. Includes aluminum weld-in bung, connector plug with flying lead & sensor.ĭuralast GM air intake temperature sensor female pigtail harness. STM UNIVERSAL GM AIR INTAKE TEMPERATURE SENSOR KITįor a less expensive option to the AEM sensors, The STM GM Air Intake Temperature Sensor Kit includes an aluminum weld-on bung for your pipe, GM AIT sensor and matching pigtail harness.Īir inlet temperature sensor kit. The STM GM Speed Density Sensor Kit is a much more affordable alternative compared to AEM and includes the GM AIT sensor and matching harness, aluminum weld bung for your intercooler pipe and a 4 BAR Omni Power MAP Sensor. The STM Speed Density Sensor Kit includes an AEM AIT sensor with aluminum weld bung and a 4 BAR Omni Power MAP Sensor. If you're switching to Speed Density in your DSM, Evo 8 or 9, you'll need these sensors to get you on your way. NGK / NTK replacement oxygen sensor sensor for the AFX wideband monitor. Compatible with Innovate Motorsports LM-2, LC-2, and MTX-L, SCG-1, DLG-1, PSB-1, and PSN-1. Compatible with Innovate Motorsports LM-1, LM-2, LC-1, and LC-1ST.īosch LSU 4.9 5-Wire Wide-Band O2 Sensor. MN153010,1588A064,MR578532,MN191125,1588A119ĪEM REPLACEMENT 4.9LSU BOSCH OXYGEN SENSORĪEM Replacement 4.9LSU Bosch Oxygen Sensor for new AEM Digital Wideband UEGO Air/Fuel Gauge 30-4110.ĪEM REPLACEMENT 4.2LSU BOSCH OXYGEN SENSORĪEM Replacement 4.2LSU Bosch Oxygen Sensor for original AEM Wideband UEGO Air/Fuel Gauges.Īuto Meter Narrow Band O2 Sensor Kit for use with narrow band air/fuel ratio gauges.īosch LSU 4.2 5-Wire Wide-Band O2 Sensor. Front and rear O2 sensors available for all VIII-IX model years. 3, 4 and 6mm sizes.ĮVOLUTION VIII-IX - OXYGEN SENSORS & PARTS High quality, thick-walled, pure silicone hose in 3mm, 4mm and 6mm.īlack T Vacuum Fittings. Sold in a 10 foot roll and available in three diameters: 5/32", 3/8" and 1/4". Suitable for air lines and instrumentation and capable of Withstanding operating pressures up to 100 PSI and temperatures up to 140☏. PROFITTER 500° LOW DENSITY PTFE PIPE TAPEįlexible, lightweight and durable. It has excellent resistance to: abrasion, moisture, alkalies, acid, copper corrosion and varying weather conditions. Scotch® Vinyl Electrical Tape 33 is a quality, general-purpose vinyl insulating tape. 4AN Male to 1/8 NPT Female Adapter Fitting. 4AN MALE TO 1/8 NPT FEMALE ADAPTER FITTING 1/8" NPT Female to 1/8" BSPT Male Adapter. Does not accommodate fuel pressure or models 5423 & 5426.Īutometer Metric Gauge Adapter. Each adapter features an 1/8 NPT fitting.Īuto Meter Nylon Tubing for Mechanical Pressure Gauges. Four sizes are available for the perfect fit for just about any engine application and stays water-tight to prevent leaks with the provided hose clamps. This will place the temperature sensor directly in the stream of the water towards the radiator without absorbing transient heat from the engine block for accurate readings of the water temperature. M20 x 1.5 fits most Subaru, Non-metric Honda, Mitsubishi, Acura, Hyundai, Nissan Sentra 2.5L & Mazda RX-7, RX-8 & S2000. This plate screws on under your oil filter and it has 4 1/8"NPT fittings. This is a great product from Prosport to make installing your Oil Pressure and Oil Temperature senders easy. PROSPORT OIL FILTER ADAPTER PLATE (M20 x 1.5) Trying to find a power source for your gauges? These nifty, little things will do the trick!
This allows you to tap your mechanical gauge that uses the 1/8 tubing as a feed line.
EMS 8860 O2 SENSOR INSTALL
The STM Evo VIII-IX Water Neck starts with an OEM Mitsubishi piece, modified to accommodate a 1/8" NPT bung for a clean install with your water temperature sensor & gauge. STM EVO 8/9 WATER NECK WITH NPT TEMP SENSOR BUNG The STM Remote Oil Pressure Line Kit includes everything needed to take your oil psi gauge reading from the oil filter housing. STM EVO 8/9 REMOTE OIL PRESSURE LINE KIT (OIL FILTER HOUSING)
Works with both 4G63 and 4B11 Evolution 8/9/X. The STM Remote Oil Pressure Line Kit works with 1/8" NPT gauges and installs in place of your factory oil pressure switch in the back of your engine block allowing you to relocate your new oil pressure sending unit away from the harsh vibrations of the engine, keeping your sending unit safe and prolonging life. STM EVO 8/9 REMOTE OIL PRESSURE LINE KIT (BACK OF BLOCK)
0 kommentar(er)
